Turmalina Discovers High-Grade Gold Vein System Including 17.9 g/t Au Over 1.18 m
Turmalina Discovers High-Grade Gold Vein System Including 17.9 g/t Au Over 1.18 m
This news release is not for distribution to U.S. newswire services for dissemination in the United States
Vancouver, BC – October 10, 2023 – Turmalina Metals Corp. (“Turmalina” or the “Company”) (TSXV:TBX – OTCQX:TBXXF – WKN:A2PVJL) is pleased to announce the discovery of a high-grade gold vein system and a new copper-gold mineralized breccia pipe following the successful completion of 2,984 m of diamond drilling at the Company’s 403 km2 San Francisco project located in the prolific mining province of San Juan, Argentina (the “Project” or “San Francisco”). The recently completed 22-hole program included maiden drilling at 5 targets over the extensive project area (Figure 3).
Initial mapping and sampling at Veta Rica defined a low-sulfidation epithermal quartz vein, 1 to 6 m wide, outcropping over 300 meters of strike length that returned rock chip assays of up to 56 g/t Au (Figures 1 5). Two holes were drilled from the same drill pad with both intersecting high-grade gold at depth (see core photos in Figure 4) including:
4.4 m @ 6.4 g/t Au; SFDH-078 from 36.6 m. Including 0.5 m @28.6 g/t Au from 36.6 m. And 0.45 m @ 14.12 g/t Au from 38.85 m. 8.75 m @ 3.5 g/t Au; SFDH-079 from 42 m. Including 6.0 m @ 4.6 g/t Au from 42 m. Including 1.18 m @ 17.9 g/t Au from 42 m.
Follow up mapping has defined a series of epithermal veins extending for up to 1.5 km, both along strike, and parallel with, the drilled Veta Rica vein, with assay results pending (Figure 5). Mapping is ongoing and the system remains open along strike and at depth. The Project area is located within a known epithermal gold belt: The nearest such epithermal system is located at Austral Gold’s Casposo mine, 70 km south of the Veta Rica discovery. Casposo produced, between 2011 and 2015, 283,000 oz of gold and 9.6M oz of silver with average grades of 4.8 g/t Au and 183 g/t Ag. Between 2017 and 2019 another 32,000 oz of gold and 3 M oz of silver were produced before the mill was placed back into care and maintenance.
Figure 1: Veta Rica Surface map and sections showing drill holes. Rock chip sampling of the Veta Rica vein 300m west of the drill target returned grades of up to 27 g/t Au. If image is not shown, please click here: https://cdn.investor-files.net/2023_10_10_TBX_News1_6b56d50ecf.png
The drilling program also tested the Ethan breccia pipe, a large (~ 200 m long by 100 m wide; Figure 7) tourmaline breccia pipe that returned strong surface trench assays (i.e. 30m @ 0.8 % Cu). Two reverse circulation (RC) and three diamond holes were drilled at the Ethan Breccia. These scout holes intercepted the strongest tourmaline breccia mineralization discovered to date at the Project outside of the high-grade San Francisco breccia, with intercepts including:
31 m @ 0.42 % Cu, 0.31 g/t Au 2 g/t Ag (0.66 % CuEq); SFRC-061 from 3 m. Including 10 m @ 0.72 % Cu, 0.53 g/t Au 5 g/t Ag (1.2 % CuEq) from 6 m. 8 m @ 0.71 % Cu, 0.68 g/t Au 1 g/t Ag (1.2 % CuEq); SFDH-062 from 27 m. 33.8 m @ 0.45 % Cu, 0.18 g/t Au 5 g/t Ag (0.63 % CuEq); SFDH-063 from surface. Including 14 m @ 0.72 % Cu, 0.16 g/t Au 9 g/t Ag (0.93 % CuEq) from surface
Mr James Rogers, Chief Executive Officer, states:
“We are very pleased to announce that the San Francisco project has delivered Turmalina an exciting development with the discovery of high-grade gold in the extensive Veta Rica epithermal vein system. This mineralization is similar to that of several epithermal mines located along-strike of our project, including Austral Gold’s Casposo Mine, located 70 km to the south. Ony two holes have been drilled into this new discovery, and both holes have returned grades of over 17 g/t Au. Ongoing surface work has already extended the strike length of the vein system from 300 m to over 1.5 km. To have intercepted high-grade gold veins in such a prolific epithermal gold district continues to demonstrate the value of our large land package in San Juan: the largest gold producer and most mining-friendly state in Argentina.
While the San Francisco breccia pipe is an outstanding high-grade asset, we are pleased to add the Ethan Breccia to our portfolio of mineralized breccias. It’s encouraging to see the strong copper mineralization in shallow drilling at Ethan, a breccia pipe that is nearly four times the width of the San Francisco pipe, and our team is currently reviewing and modelling the results.”
Figure 2: Veta Rica discovery hole drill core being examined by CEO James Rogers. If image is not shown, please click here: https://cdn.investor-files.net/2023_10_10_TBX_News2_e4e2fbb0b3.png
Three other prospects were tested during the program. Eight holes were drilled to test intrusion-hosted stockwork veining at Tres Magos, returning multiple short intervals of Ag-Pb-Zn±Cu-Au mineralization (i.e. 1.3m of 0.5% Cu, 13 g/t Ag, 0.3 % Pb 0.4 % Zn; 0.9 % CuEq, SFDH-076 from 51.8 m). Three holes were drilled to test intermediate sulfidation epithermal veins at Veta Amarilla, which returned short intervals of Ag-Au-Pb-Zn mineralization (i.e. 1 m @ 18 g/t Ag, 0.3 g/t Au, 0.5 % Pb 0.2 % Zn; 0.5 % CuEq, SFDH-071 from 28 m). Three holes testing low sulfidation epithermal quartz veins at Veta Alumbrera did not return any significant results. Intersections for all prospects are listed in Table 2.
Figure 3: Map showing the block of properties controlled by Turmalina Metals with the drill targets locations drilled in this campaign and the San Francisco Breccia. If image is not shown, please click here: https://cdn.investor-files.net/2023_10_10_TBX_News3_c37d277388.png
Current Work
Initial exploration efforts at San Francisco were focussed on breccia mineralization. Through the Company’s extensive exploration work, led by Chico Azevedo, the project has greatly expanded into highly prospective areas containing a number of vein, intrusion-related, porphyry and breccia targets.
While the San Francisco breccia pipe remains one of the highest-grade tourmaline Cu-Au breccia pipes ever discovered (see select results in Table 1) the Company is most excited about the exploration potential for high-grade gold-silver and polymetallic vein types and other mineralization styles. The Veta Rica discovery exemplifies the style of epithermal mineralization commonly found in the district.
The Turmalina technical team is currently in the field continuing surface work on the new Veta Rica discovery along with other nearby targets. A follow up diamond drilling program is currently being planned to further test the Veta Rica target along strike and at depth. Our team is also currently modelling the Ethan Breccia discovery with an aim of designing follow-up drill holes in this large breccia system.
Grant of Stock Options and RSUs
The Company announces that it has granted options to acquire a total of 1,225,000 common shares of the Company to officers, directors, employees, and consultants, pursuant to the Company's Stock Option Plan, at the exercise price of $0.35 per share for a period of five years.
Additionally, the Company has granted 5,400,000 restricted stock units (“RSUs”) to officers, directors, employees, and consultants of the Company under the terms of the Company’s restricted share unit plan (the “RSU Plan”) and which have a two-year vesting period.
About The San Francisco Project
The 40,340 ha San Francisco project is located in the pro-mining province of San Juan, Argentina, a country where there are currently 12 operating mines, 5 in construction and 20 in pre-feasibility/feasibility stage. The project benefits from well-developed infrastructure and is 130 km northeast of the regional capital San Juan.
The San Francisco Project was assembled around, and includes, one of the highest-grade tourmaline breccias of the same name. The land position at San Francisco was expanded in 2022 and now includes multiple mineralized targets including more than 60 breccias, intrusion-related gold and epithermal vein-type targets.
Turmalina has developed an operational centre in the town of Villa Nueva, where the local community welcomes new exploration efforts in the region.
Turmalina has several option agreements to acquire 100% of certain titles of the SFDLA project and a right to explore and exploit other titles from the government of San Juan.
Table 1: Selected highlight of previous Company drilling at the San Francisco Breccia Pipe
Hole ID
Target
From (m)
To (m)
Interval (m)
Au (g/t)
Ag (g/t)
Cu (%)
Pb (%)
Zn (%)
AuEq g/t
CuEq %
SFDH-012
SF BX
12
121
109
4.94
109
1.13
0.23
0.06
8.00
5.49
SFDH-039
SF BX
397.7
470
72.3
0.71
100
3.47
0.31
0.69
7.07
4.85
SFDH-038
SF BX
0
81
81
2.33
63.94
0.23
0.23
0.38
3.50
2.40
SFDH-011
SF BX
25
108
83
4.4
82
0.43
0.74
0.52
6.09
4.18
SFDH-011
SF BX
27
68
41
7.03
91
0.51
0.23
0.02
8.96
6.14
*Intersections are not true widths and additional drilling and geological modelling of the mineralized zones in the breccia pipes is required to determine the true widths of the drill hole intersections. Intersections are selected based on a 0.5 g/t Au or 0.3% Cu cut-off grade, a minimum downhole length of 2m and a maximum waste inclusion of 2 consecutive meters. Equivalent gold (AuEq) and equivalent copper (CuEq) values are calculated assuming 100% recovery using USD$ 1770 oz Au, $23 oz Ag and $8300/t Cu (~$3.8/lb). Results from the drilling on this project can be found in Company News releases with the following dates: March 23, August 28, October 5 December 7, 2020 and January 25, March 30, June 8 August 30 2021.
On Behalf of the Company:
James Rogers
Chief Executive Officer and Director
Web: www.turmalinametals.com
Address: #488 – 1090 West Georgia St., Vancouver, BC, V6E 3V7
For Investor Relations enquiries, please contact Bryan Slusarchuk at +1 833 923 3334 (toll free) or via info@turmalinametals.com.
About this press release:
In Germany this press release is brought to you by https://www.aktien.news – your German news platform for international commodity stocks. For more information visit https://akt.ie/nnews
Statements
About Turmalina Metals and our projects: Turmalina Metals is a TSXV-listed exploration company focused on developing our portfolio of high-grade gold-copper-silver projects in South America. Our focus is on tourmaline breccias, a deposit style overlooked by many explorers. Turmalina Metals is led by a team responsible for multiple gold-copper-silver discoveries who are highly experienced in this deposit style. Our projects are characterised by open high-grade mineralization on established mining licenses that present compelling drill targets. The principal project held by Turmalina is the San Francisco project in San Juan, Argentina. For further information on the San Francisco Project, refer to the technical report entitled “NI43-101 Technical Report San Francisco Copper Gold Project, San Juan Province, Argentina” dated November 17, 2019 under the Corporation’s profile at www.sedar.com. Turmalina is also exploring the Chanape project in Peru. For further information on Chanape please refer to the technical report “National Instrument 43-101 Technical Report on the Chanape Gold-Silver-Copper Project” dated July 5, 2022 under the Corporation’s profile at www.sedar.com.
Sampling and Analytic procedure: Turmalina Metals follows systematic sampling and analytical protocols which exceed industry standards and are summarized below.
All drill holes are PQ, HQ or NQ diameter diamond core holes. At Chanape drill core is collected at the drill site and transported by vehicle to the Turmalina core logging facility in San Damian where recovery measurements are taken before the core is photographed and geologically logged. The core is then cut in half with a diamond saw blade with half the sample retained in the core box for future reference and the other half placed into a pre-labelled plastic bag, sealed with a plastic zip tie, and identified with a unique sample number. The core is typically sampled over a 0.5 to 1.5 meter sample interval unless the geologist determines the presence of an important geological contact. In this case, the samples can have a minimum of 20 centimetres length. The bagged samples are then stored in a secure area pending shipment to the ALS laboratory in Lima where they are dried, crushed and pulverized. Following sample preparation the prepared pulps are then analysed using a 50g digested sample and fire assay-AA finish analysis for gold and four acid digestion with ICP-MS analysis for 53 other elements. Samples with results that exceed maximum detection values for gold are re-analysed by fire assay with a gravimetric finish and other elements of interest are re-analysed using precise ore-grade ICP analytical techniques.
Turmalina Metals independently inserts certified control standards, coarse field blanks and duplicates into the sample stream to monitor data quality (‘QA/QC’ samples). These QA/QC samples are inserted “blindly” to the laboratory in the sample sequence prior to departure from the Turmalina Metals core storage facilities. For drill core samples 8 QA/QC samples are inserted into each 70-sample dispatch: 1 blank sample, 5 commercially-prepared standards, 1 core duplicate sample and 1 control sample from the SF mine.
The assay results for the QA/QC samples are checked and verified by the project geologist and the Qualified Person. All such QA/QC assay results from sample dispatches reported in this news release have been found to be within acceptable industry limits, and the Qualified Person is not aware of any sampling, recovery or any other factors that could materially affect the accuracy or reliability of the data.
Qualified Person: The scientific and technical data contained in this news release pertaining to the San Francisco and Turmalina projects has been reviewed and approved by Dr. Rohan Wolfe, Technical Advisor, MAIG, who serves as the Qualified Person (QP) under the definition of National Instrument 43-101.
Forward Looking Statement: This news release contains certain "forward-looking statements" within the meaning of such statements under applicable securities law. Forward-looking statements are frequently characterized by words such as "anticipates", "plan", "continue", "expect", "project", "intend", "believe", "anticipate", "estimate", "may", "will", "potential", "proposed", "positioned" and other similar words, or statements that certain events or conditions "may" or "will" occur. These statements are only predictions. Various assumptions were used in drawing the conclusions or making the projections contained in the forward-looking statements throughout this news release. Forward-looking statements are based on the opinions and estimates of management at the date the statements are made and are subject to a variety of risks (including those risk factors identified in the Corporation’s prospectus dated November 21, 2019) and uncertainties and other factors that could cause actual events or results to differ materially from those projected in the forward-looking statements. The Corporation is under no obligation, and expressly disclaims any intention or obligation, to update or revise any forward-looking statements, whether as a result of new information, future events or otherwise, except as expressly required by applicable law.
Attachments:
Figure 4: Veta Rica drill core from drill hole SFDH-079 with gold grades (g/t). If image is not shown, please click here: https://cdn.investor-files.net/2023_10_10_TBX_News4a_d8a1fc7aac.png
Figure 5: Follow up mapping and sampling at Veta Rica area has already defined a series of quartz veins along-strike and in parallel to the drilled outcrop. This low sulfidation epithermal system has been mapped up to 1.5km from the drill site, and remains open along-strike and at depth. Detailed sampling of all veins is underway, with assays pending. Numbers refer to photos in Figure 6. If image is not shown, please click here: https://cdn.investor-files.net/2023_10_10_TBX_News4_31502e24e4.png
Figure 6: Photographs from the current Veta Rica sampling program (locations in Figure 4): (1) low sulphidation epithermal quartz vein hosted in strongly sericite-altered granodiorite. (2) ) Quartz vein displaying strong boxwork texture (hematite and jarosite) after weathered sulphides. Assays for both sites pending. If image is not shown, please click here: https://cdn.investor-files.net/2023_10_10_TBX_News5_77da668de8.png
Figure 7: Geological map of the Ethan breccia with samples and drill hole locations. Drilling has shown that the two lobes mapped at surface represent one breccia body measuring 200m by 100 m at the surface. If image is not shown, please click here: https://cdn.investor-files.net/2023_10_10_TBX_News6_98b2cc393a.png
Figure 8: Cross section at the Ethan Breccia. Hole SFDH-63 was drilled parallel to hole SFRC-061, which was lost at 69m and had intersected 31m @ 0.66% of CuEq. The Company is currently modelling the distribution of grade in this large breccia body. If image is not shown, please click here: https://cdn.investor-files.net/2023_10_10_TBX_News7_f226a868fb.png
Figure 9: Cu-Au breccia mineralization at Breccia Ethan (A) Typical quartz-tourmaline-pyrite-chalcopyrite-chalcocite breccia (SFDH-063, 13 to 40 m). (B) Strong malachite staining of a quartz-tourmaline breccia. From a 0.9m long sample that returned 0.79 g/t Au, 5.8 g/t Ag 0.66 % Cu (SFDH-063, 21.75-22.65m). Photographs are of a selected interval and is not necessarily representative of mineralisation hosted throughout the property. If image is not shown, please click here: https://cdn.investor-files.net/2023_10_10_TBX_News8_1fced13cf6.png
Table 2: Significant drillhole intersections from 2023 drilling at the San Francisco Project
Prospect
Hole_ID
From
To
Interval
Au (g/t)
Ag (g/t)
Cu (%)
Pb (%)
Zn (%)
EqAu (g/t)
EqCu (%)
Breccia Ethan
SFRC-061
3
34
31
0.31
2.06
0.42
0.00
0.01
0.93
0.66
Breccia Ethan
SFRC-061
including
6
16
10
0.53
4.54
0.74
0.00
0.01
1.62
1.16
Breccia Ethan
SFRC-061
57
60
3
0.36
0.68
0.27
0.00
0.00
0.75
0.54
Breccia Ethan
SFRC-062
2
7
5
0.39
0.96
0.18
0.00
0.01
0.66
0.47
Breccia Ethan
SFRC-062
27
35
8
0.68
1.31
0.71
0.00
0.01
1.69
1.21
Breccia Ethan
SFDH-063
0
33.8
33.8
0.18
4.78
0.45
0.02
0.03
0.89
0.63
Breccia Ethan
SFDH-063
Including
0
14
14
0.16
9.33
0.72
0.04
0.05
1.31
0.93
Breccia Ethan
SFDH-063
Including
57.12
63
5.88
0.27
0.53
0.24
0.00
0.00
0.61
0.43
Breccia Ethan
SFDH-063
79.32
90.15
10.83
0.28
1.07
0.34
0.00
0.00
0.76
0.54
Breccia Ethan
SFDH-064
25.3
29.3
4
0.25
0.91
0.37
0.00
0.01
0.78
0.56
Breccia Ethan
SFDH-064
48.37
54.45
6.08
0.14
0.67
0.21
0.00
0.00
0.45
0.32
Breccia Ethan
SFDH-064
68.7
75
5.99
0.21
0.93
0.22
0.00
0.00
0.53
0.38
Breccia Ethan
SFDH-065
67.35
70.65
3.3
0.25
0.44
0.18
0.00
0.00
0.51
0.36
Breccia Ethan
SFDH-065
108.25
112.7
4.45
0.14
0.67
0.19
0.00
0.00
0.41
0.30
Tres Magos
SFDH-066
141.4
144
2.6
0.24
0.79
0.00
0.02
0.03
0.27
0.19
Tres Magos
SFDH-067
29.7
32.6
2.9
0.01
0.03
0.34
0.00
0.03
0.50
0.35
Tres Magos
SFDH-068
18.55
39.1
20.55
0.27
0.09
0.00
0.00
0.01
0.28
0.20
Tres Magos
SFDH-070
45.25
50.65
5.4
0.02
4.07
0.04
0.40
0.50
0.48
0.35
Veta Amarilla
SFDH-071
28
29
1
0.25
17.90
0.02
0.50
0.17
0.75
0.54
Veta Amarilla
SFDH-072
20
20.65
0.65
0.22
7.41
0.01
0.49
0.23
0.60
0.43
Veta Amarilla
SFDH-072
84
85.8
1.8
0.01
8.50
0.04
0.09
0.30
0.32
0.23
Veta Amarilla
SFDH-073
3.65
7.35
3.7
0.01
0.01
0.00
0.02
0.35
0.17
0.12
Tres Magos
SFDH-076
Including
51.8
53.1
1.3
0.04
13.45
0.53
0.32
0.42
1.24
0.88
Tres Magos
SFDH-076
91.3
95.3
4
0.46
7.46
0.07
0.07
0.06
0.70
0.50
Tres Magos
SFDH-076
Including
93.55
95.3
1.75
0.93
9.13
0.09
0.05
0.04
1.20
0.86
Tres Magos
SFDH-077
99.9
100.65
0.75
0.34
10.54
0.05
0.39
0.72
0.98
0.70
Tres Magos
SFDH-077
106.9
107.57
0.67
1.03
4.88
0.03
0.03
0.03
1.15
0.82
Veta Rica
SFDH-078
36.6
41
4.4
6.36
4.97
0.00
0.07
0.00
6.45
4.61
Veta Rica
SFDH-078
Including
36.6
37.1
0.5
28.59
12.44
0.00
0.17
0.00
28.80
20.57
Veta Rica
SFDH-078
and
38.85
39.3
0.45
14.12
4.93
0.00
0.01
0.00
14.19
10.13
Veta Rica
SFDH-079
42
70.36
28.36
1.33
1.44
0.00
0.04
0.02
1.37
0.98
Veta Rica
SFDH-079
Including
42
50.75
8.75
3.52
1.36
0.00
0.03
0.01
3.56
2.54
Veta Rica
SFDH-079
Including
42
48
6
4.53
1.54
0.00
0.03
0.01
4.57
3.26
Veta Rica
SFDH-079
Including
42
43.18
1.18
17.94
3.32
0.00
0.05
0.01
18.00
12.86
Veta Rica
SFDH-079
54.45
56.6
2.15
0.89
0.84
0.00
0.04
0.02
0.93
0.66
Veta Rica
SFDH-079
60
67.56
7.56
0.50
2.82
0.01
0.07
0.04
0.59
0.42
Veta Rica
SFDH-079
Including
63.15
64.23
1.08
1.26
4.74
0.01
0.17
0.06
1.43
1.02
*Intersections are not true widths and additional drilling and geological modelling of the mineralized zones in the breccia pipes is required to determine the true widths of the drill hole intersections. Equivalent gold (AuEq) and equivalent copper (CuEq) values are calculated assuming 100% recovery using USD$ 1860 oz Au, $22 oz Ag, $8100/t Cu (~$3.7/lb), $2130/t Pb $2510/t Zn.
Table 3: San Francisco RC and diamond drill hole locations and targets included in this release. Holes listed but not reported in Table 2 returned no significant results.
Hole ID
E
(WGS84 - 19S)
N
(WGS84 - 19S)
Elevation (m)
Azimuth
Dip
Depth (m)
Target
SFRC-061RC
444973
6603690
3398
161
-60
69
Breccia Ethan
SFRC-062RC
444972
6603691
3398
316
-60
47
Breccia Ethan
SFDH-063
444971
6603690
3398
161
-61
206
Breccia Ethan
SFDH-064
444973
6603692
3395
316
-60
161
Breccia Ethan
SFDH-065
441189
6599844
3398
29
-60
147.4
Breccia Ethan
SFDH-066
441093
6600004
3301
280
-62
167.4
Tres Magos
SFDH-067
441418
6599987
3499
6
-58
134
Tres Magos
SFDH-068
441279
6600016
3318
102
-61
50.8
Tres Magos
SFDH-069
441188
6599845
3259
281
-62
76.5
Tres Magos
SFDH-070
441288
6600402
3279
105
-60
156
Tres Magos
SFDH-071
440035
6604044
3382
165
-60
125
Veta Amarilla
SFDH-072
440035
6604044
3381
165
-80
224
Veta Amarilla
SFDH-073
440202
6604214
3387
166
-60
119
Veta Amarilla
SFDH-074
439896
6603771
3383
329
- 60
116
Veta Amarilla
SFDH-075
441421
6600000
3485
189
-62
83
Tres Magos
SFDH-076
441072
6600697
3542
304
-61
119
Tres Magos
SFDH-077
441126
6600524
3541
345
-60
134
Tres Magos
SFDH-078
446351
6594462
2879
194
-60
63.5
Veta Rica
SFDH-079
446347
6594467
2875
219
-60
84.8
Veta Rica
SFDH-080
446271
6567555
1837
74
-59
269
Veta Alumbrera
SFDH-081
446130
6567975
1921
82
-60
131
Veta Alumbrera
SFDH-082
445967
6567852
1935
60
-65
416
Veta Alumbrera